MYZR-SSD2351-EK112快速启动手册 ================================ 准备工作 ~~~~~~~~~ | 开发板：1个 | TYPEC数据线：1条 | TTL串口模块：1个 | 杜板线：若干 | 网线：1根 串口软件设置 ~~~~~~~~~~~~~ | 波特率：115200 | 数据位：8bit | 停止位：1bit | 校验位：none 拨码设置以及TTL串口模块 ~~~~~~~~~~~~~~~~~~~~~~~ 拨码设置 --------- | 启动拨码模式：1: on， 2: on， 3: off， 4 : off TTL串口模块接法 ---------------- | 座子：J3 | 按以下CPU的对应端和TTL模块的管脚连接起来 +---------+-------------------------+-------------+---------+ | CPU端： | J3_1:RX管脚(正方形焊盘) | J3_2:TX管脚 | J3_3:地 | +=========+=========================+=============+=========+ | TTL端： | TX管脚 | RX管脚 | GND | +---------+-------------------------+-------------+---------+ 串口启动 ~~~~~~~~~~ .. code-block:: shell #用TTL模块，把电脑和板子连接起来。插入TYPEC线，开机 提示信息如下： IPL gf7fc380 D-19 CPU=800MHz HEAP: [0xa0018330~0xa0018430] SHM: [0xa0013830~0xa0018330] RECORD: tc at 0xa00138c0 HW Reset SPI 104M [SPINAND] RFC use command 0x6b [SPINAND] dummy clock 0x8 [SPINAND] Program with command 0x32. [SPINAND] Random with command 0x34. [FLASH] BDMA mode. Loading Environment from SPIFlash... OK QFN128 NTC1G DDR3 DFS(2133, 800) miu pll: 300MHz DRAM Size: 128MB ddr train finish HEAP: [0x23d00000~0x23e00000] SHM: [0x22440000~0x23d00000 0x7dbd3830] IMG_LOAD@ devs:0xa img:CUST bak:0 ofs:0x0 sz:0x580 dst:0x23d00000 IMG_LOAD@ devs:0xa img:CUST bak:0 ofs:0x0 sz:0x7520 dst:0x22400000 IMG_VERIFY@ type:1 DECOMP@0 from 0x22400000 to 0x22400000 Flashing D-Cache and Disabling MMU OS_JUMP@ method:1 entry_pointer:0x22400000 IPL_CUST gf7fc380 D-19 HEAP: [0x23d00000~0x23e00000] RECORD: moving tc from 0x22440090 to 0x263ff000 SPI 104M IMG_LOAD@ devs:0xa img:TFA bak:0 ofs:0x0 sz:0x580 dst:0x23d00000 IMG_LOAD@ devs:0xa img:TFA bak:0 ofs:0x0 sz:0xc10a dst:0x263fffc0 IMG_VERIFY@ type:2 DECOMP@0 from 0x26400000 to 0x26400000 IMG_LOAD@ devs:0xa img:UBOOT bak:0 ofs:0x0 sz:0x580 dst:0x23d00580 IMG_LOAD@ devs:0xa img:UBOOT bak:0 ofs:0x0 sz:0x55268 dst:0x22444680 IMG_VERIFY@ type:4 DECOMP@2 from 0x224446c0 to 0x23e00000 Flashing D-Cache OS_JUMP@ method:2 entry_pointer:0x23e00000 U-Boot 2021.10 (Mar 03 2025 - 07:57:25 +0000) SoC: SigmaStar pcupid Model: PCUPID Version: P###g####### DRAM: 128 MiB WDT: Not found! NAND: SPI 104M [SPINAND] RFC use command 0x6b [SPINAND] dummy clock 0x8 [SPINAND] Program with command 0x32. [SPINAND] Random with command 0x34. [FLASH] BDMA mode. spi clk already initialized [FLASH] dev_id = 0xee [FLASH] mfr_id = 0xc8, dev_id= 0x91 id_len = 0x2 128 MiB MMC: Fail to get pad(0x20309) ip(0x2_8) form padmux ! Fail to get pad(0x20003) ip(0x0_2) form padmux ! MSC: 0, MSC: 1 Loading Environment from NAND... ENV: offset = 0x4c0000 size = 0x40000 ENV1: offset = 0x500000 size = 0x40000 OK In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 firmwarefs_open: open PQ.bin fail(-2) JPD_SW_decode time: 74259 us JPD_SW_decode time: 13134 us cost time: 508815 us bitwidth = 16 ## Booting kernel from Legacy Image at 23000000 ... Image Name: MVX4##P###g#######KL_LX601##[BR: Image Type: ARM Linux Kernel Image (lzma compressed) Data Size: 3436492 Bytes = 3.3 MiB Load Address: 20008000 Entry Point: 20008000 Verifying Checksum ... OK Uncompressing Kernel Image [XZ] !!!reserved 0x22000000 length=0x 1000000 for xz!! XZ: uncompressed size=0x9651ec, ret=7 Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 6.1.111-rt42 (tangbin@myzr-u2004) (arm-sigmastar-linux-uclibcgnueabihf-12.4.0-gcc (crosstool-NG 1.26.0) 12.4.0, GNU ld (crosstool-NG 1.26.0) 2.40) #120 SMP PREEMPT Wed Mar 5 04:14:41 UTC 2025 CPU: ARMv7 Processor [411fd040] revision 0 (ARMv7), cr=50c5383d CPU: div instructions available: patching division code CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache early_atags_to_fdt() success .. code-block:: shell OF: fdt: Machine model: PCUPID LXmem is 0x8000000 PHYS_OFFSET is 0x20000000 Add mem start 0x20000000 size 0x8000000!!!! LX_MEM = 0x20000000, 0x8000000 LX_MEM2 = 0x0, 0x0 LX_MEM3 = 0x0, 0x0 MMU_MEM = 0x0, 0x0 EMAC_LEN= 0x0 DRAM_LEN= 0x0 Memory policy: Data cache writealloc OF: reserved mem: invalid size property in 'cma0' node. deal_with_reserved_mmap memblock_reserve success mmap_reserved_config[0].reserved_start= 0x26800000 deal_with_reserve_mma_heap memblock_reserve success mma_config[0].reserved_start= 0x27600000 size:a00000 deal_with_reserve_mma_heap memblock_reserve success mma_config[1].reserved_start= 0x25cf7000 size:708000 cma: Reserved 16 MiB at 0x24c00000 Zone ranges: Normal [mem 0x0000000020000000-0x00000000275fffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000020000000-0x0000000025cf6fff] node 0: [mem 0x00000000263ff000-0x00000000275fffff] Initmem setup node 0 [mem 0x0000000020000000-0x00000000275fffff] On node 0, zone Normal: 776 pages in unavailable ranges psci: probing for conduit method from DT. psci: PSCIv1.1 detected in firmware. psci: Using standard PSCI v0.2 function IDs psci: MIGRATE_INFO_TYPE not supported. psci: SMC Calling Convention v1.2 percpu: Embedded 11 pages/cpu s15584 r8192 d21280 u45056 Built 1 zonelists, mobility grouping on. Total pages: 28172 Kernel command line: ubi.mtd=ubia,2048 root=/dev/mtdblock7 rootfstype=squashfs ro init=/linuxrc LX_MEM=0x8000000 mma_heap=mma_heap_name0,miu=0,sz=0xA00000 mma_memblock_remove=1 cma=16M mma_heap=mma_heap_fb,miu=0,sz=0x708000 mmap_reserved=fb,miu=0,sz=0x800000,max_start_off=0x6800000,max_end_off=0x7000000 mtdparts=nand0:1792k@1280k(BOOT),1792k(BOOT_BAK),256k(ENV),256k(ENV1),384k(DDRTRAIN),5m(KERNEL),5m(RECOVERY),6m(rootfs),768k(vendor_storage),1m(MISC),107136k(ubia) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) mem auto-init: stack:all(zero), heap alloc:off, heap free:off Memory: 77488K/113632K available (4096K kernel code, 436K rwdata, 2192K rodata, 1024K init, 157K bss, 19760K reserved, 16384K cma-reserved, 0K highmem) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 rcu: Preemptible hierarchical RCU implementation. rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 GICv3: 192 SPIs implemented GICv3: 0 Extended SPIs implemented GICv3: GICv3 features: 16 PPIs GICv3: CPU0: found redistributor 0 region 0:0x16080000 sstar_main_intc_init: np->name=sstar_main_intc, parent=gic sstar_pm_main_intc_init: np->name=sstar_pm_main_intc, parent=sstar_main_intc sstar_gpi_intc_init: np->name=sstar_gpi_intc, parent=sstar_main_intc sstar_pm_gpi_intc_init: np->name=sstar_pm_gpi_intc, parent=sstar_main_intc rcu: srcu_init: Setting srcu_struct sizes based on contention. [hal_clk_ipupll_init] ipupll already init, skip arch_timer: cp15 timer(s) running at 6.00MHz (virt). clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1623fa770, max_idle_ns: 440795202238 ns sched_clock: 56 bits at 6MHz, resolution 166ns, wraps every 4398046511055ns Switching to timer-based delay loop, resolution 166ns printk: console [ttyS0] enabled Calibrating delay loop (skipped), value calculated using timer frequency.. 12.00 BogoMIPS (lpj=60000) CPU: Testing write buffer coherency: ok pid_max: default: 4096 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x20100000 - 0x20100054 rcu: Hierarchical SRCU implementation. rcu: Max phase no-delay instances is 1000. printk: console [ttyS0] printing thread started smp: Bringing up secondary CPUs ... GICv3: CPU1: found redistributor 1 region 0:0x160a0000 CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 GICv3: CPU2: found redistributor 2 region 0:0x160c0000 CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 GICv3: CPU3: found redistributor 3 region 0:0x160e0000 CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 smp: Brought up 1 node, 4 CPUs SMP: Total of 4 processors activated (48.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 40 variant 4 rev 3 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 16 (order: -2, 1024 bytes, linear) NET: Registered PF_NETLINK/PF_ROUTE protocol family DMA: preallocated 256 KiB pool for atomic coherent allocations Version : MVX4##P###g#######KL_LX601##[BR:g]#XVM platform soc: Fixed dependency cycle(s) with /soc/sstar_main_intc GPIO: probe end [Padmux]reset PAD9(reg 0x103c00:49; mask0x8000) t0 SDIO_MODE_2 (org: SD_BOOT_MODE_1) [Padmux]reset PAD79(reg 0x153f00:70; mask0x1) t0 FUART1_MODE_3 (org: OUTP_RX0_CH0_IE_CLR_MODE_0) [Padmux]reset PAD80(reg 0x153f00:70; mask0x2) t0 FUART1_MODE_3 (org: OUTN_RX0_CH0_IE_CLR_MODE_0) [Padmux]reset PAD81(reg 0x153f00:70; mask0x4) t0 FUART1_MODE_3 (org: OUTP_RX0_CH1_IE_CLR_MODE_0) [Padmux]reset PAD82(reg 0x153f00:70; mask0x8) t0 FUART1_MODE_3 (org: OUTN_RX0_CH1_IE_CLR_MODE_0) [Padmux]reset PAD83(reg 0x153f00:70; mask0x10) t0 FUART2_MODE_3 (org: OUTP_RX0_CH2_IE_CLR_MODE_0) [Padmux]reset PAD84(reg 0x153f00:70; mask0x20) t0 FUART2_MODE_3 (org: OUTN_RX0_CH2_IE_CLR_MODE_0) [Padmux]reset PAD85(reg 0x153f00:70; mask0x40) t0 FUART2_MODE_3 (org: OUTP_RX0_CH3_IE_CLR_MODE_0) [Padmux]reset PAD86(reg 0x153f00:70; mask0x80) t0 FUART2_MODE_3 (org: OUTN_RX0_CH3_IE_CLR_MODE_0) [Padmux]reset PAD96(reg 0x103c00:64; mask0x7) t0 FUART3_2W_MODE_2 (org: MIPI_TX_MODE_1) [Padmux]reset PAD96(reg 0x153400:5c; mask0x1) t0 FUART3_2W_MODE_2 (org: OUTP_CH0_IE_CLR_MODE_0) [Padmux]reset PAD97(reg 0x153400:5c; mask0x100) t0 FUART3_2W_MODE_2 (org: OUTN_CH0_IE_CLR_MODE_0) [Padmux]reset PAD16(reg 0x103e00:10; mask0x8) t0 UART5_MODE_3 (org: GPIO_MODE) hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. hw-breakpoint: maximum watchpoint size is 8 bytes. SCSI subsystem initialized pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered [MIU ERR] [sstar_miu_clk_register@532] [sstar_miu_clk_register] clk_miu enable 0 [hal_clk_mtcmos_isp_enable] clk_mtcmos_isp already enabled! Do qos-initialize Advanced Linux Sound Architecture Driver Initialized. Bluetooth: Core ver 2.22 NET: Registered PF_BLUETOOTH protocol family Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized clocksource: Switched to clocksource arch_sys_counter NET: Registered PF_INET protocol family IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 5120 bytes, linear) Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) TCP bind hash table entries: 1024 (order: 3, 40960 bytes, linear) TCP: Hash tables configured (established 1024 bind 1024) UDP hash table entries: 128 (order: 0, 6144 bytes, linear) UDP-Lite hash table entries: 128 (order: 0, 6144 bytes, linear) NET: Registered PF_UNIX/PF_LOCAL protocol family RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Initialise system trusted keyrings workingset: timestamp_bits=30 max_order=15 bucket_order=0 squashfs: version 4.0 (2009/01/31) Phillip Lougher jffs2: version 2.2. © 2001-2006 Red Hat, Inc. fuse: init (API version 7.38) Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler mq-deadline registered io scheduler kyber registered mousedev: PS/2 mouse device common for all mice i2c_dev: i2c /dev entries driver Bluetooth: HCI UART driver ver 2.3 Bluetooth: HCI UART protocol H4 registered Bluetooth: HCI UART protocol Three-wire (H5) registered SMCCC: SOC_ID: ID = jep106:0000:8192 Revision = 0x00000000 no urdma irq resource defined no urdma irq resource defined no urdma irq resource defined no urdma irq resource defined no urdma irq resource defined no urdma irq resource defined no urdma irq resource defined no urdma irq resource defined no urdma irq resource defined mdio_bus mdio-bus@emac0: ethernet-phy@0 has invalid PHY address mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 0 mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 1 [emac_phy_connect][2999] connected mac emac0 to PHY at mdio-bus@emac0:01 [uid=02430c54, driver=Generic PHY] sstar,rtcpwc 1f006800.rtcpwc: registered as rtc0 sstar,rtcpwc 1f006800.rtcpwc: setting system clock to 1970-01-01T00:28:46 UTC (1726) input: rtcpwc as /devices/soc0/soc/1f006800.rtcpwc/input/input0 [Padmux]reset PAD18(reg 0x103e00:12; mask0x8) t0 I2C2_MODE_3 (org: GPIO_MODE) [Padmux]reset PAD19(reg 0x103e00:13; mask0x8) t0 I2C2_MODE_3 (org: GPIO_MODE) [Padmux]reset PAD126(reg 0x103e00:7e; mask0x8) t0 I2C3_MODE_2 (org: GPIO_MODE) [Padmux]reset PAD125(reg 0x103e00:7d; mask0x8) t0 I2C3_MODE_2 (org: GPIO_MODE) [sstar_cpufreq_init] Current clk=800000000 request for verification of policy (0 - 2147483647 kHz) for cpu 0 verification lead to (200000 - 1450000 kHz) for cpu 0 sstar_pwm_probe: fail to config dead time sstar_pwm_probe: fail to config dead time sstar_pwm_probe: fail to config dead time sstar_pwm_probe: fail to config dead time sstar_pwm_probe: fail to config dead time sstar_pwm_probe: fail to config dead time spi 1f222000.spi: chipselect 0 already in use spi_master spi0: spi_device register error /soc/spi@1f222000/spidev@0 spi_master spi0: Failed to create SPI device for /soc/spi@1f222000/spidev@0 SPI 104M [SPINAND] RFC use command 0x6b [SPINAND] dummy clock 0x8 [SPINAND] Program with command 0x32. [SPINAND] Random with command 0x34. [FLASH] BDMA mode. [FLASH] dev_id = 0xee [FLASH] mfr_id = 0xc8, dev_id= 0x91 id_len = 0x2 nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x91 nand: Unknown nand0 nand: 128 MiB, MLC, erase size: 128 KiB, page size: 2048, OOB size: 64 nand: WARNING: nand0: the ECC used on your system (4b/512B) is too weak compared to the one required by the NAND chip (512b/4B) 11 cmdlinepart partitions found on MTD device nand0 Creating 11 MTD partitions on "nand0": 0x000000140000-0x000000300000 : "BOOT" 0x000000300000-0x0000004c0000 : "BOOT_BAK" 0x0000004c0000-0x000000500000 : "ENV" 0x000000500000-0x000000540000 : "ENV1" 0x000000540000-0x0000005a0000 : "DDRTRAIN" 0x0000005a0000-0x000000aa0000 : "KERNEL" 0x000000aa0000-0x000000fa0000 : "RECOVERY" 0x000000fa0000-0x0000015a0000 : "rootfs" 0x0000015a0000-0x000001660000 : "vendor_storage" 0x000001660000-0x000001760000 : "MISC" 0x000001760000-0x000008000000 : "ubia" Err: Could not get dts [wakeup] option! wakeup: probe of soc:wakeup failed with error 1 sstar-asoc-card soc:asoc_sound: i = 0, codec_name = sstar-dummy-codec1 sstar-bach 1f2a0400.bach1: pcmC0 dma buffer size 0x40000 sstar-bach 1f2a0400.bach1: physical dma address 0x24c50000 sstar-bach 1f2a0400.bach1: miu address 0x04c50000 sstar-bach 1f2a0400.bach1: virtual dma address (ptrval) sstar-bach 1f2a0400.bach1: pcmP0 dma buffer size 0x100000 sstar-bach 1f2a0400.bach1: physical dma address 0x24c90000 sstar-bach 1f2a0400.bach1: miu address 0x04c90000 sstar-bach 1f2a0400.bach1: virtual dma address (ptrval) sstar-asoc-card soc:asoc2_sound: i = 0, codec_name = sstar-dummy-codec2 sstar-bach 1f2a0400.bach2: pcmC1 dma buffer size 0x40000 sstar-bach 1f2a0400.bach2: physical dma address 0x24d90000 sstar-bach 1f2a0400.bach2: miu address 0x04d90000 sstar-bach 1f2a0400.bach2: virtual dma address (ptrval) sstar-bach 1f2a0400.bach2: pcmP1 dma buffer size 0x40000 sstar-bach 1f2a0400.bach2: physical dma address 0x24dd0000 sstar-bach 1f2a0400.bach2: miu address 0x04dd0000 sstar-bach 1f2a0400.bach2: virtual dma address (ptrval) sstar-asoc-card soc:asoc2_sound: ASoC: driver name too long 'sstar-asoc2-card' -> 'sstar-asoc2-car' sstar-asoc-card soc:asoc3_sound: i = 0, codec_name = sstar-dummy-codec3 sstar-bach 1f2a0400.bach3: pcmC0 dma buffer size 0x40000 sstar-bach 1f2a0400.bach3: physical dma address 0x24c50000 sstar-bach 1f2a0400.bach3: miu address 0x04c50000 sstar-bach 1f2a0400.bach3: virtual dma address (ptrval) sstar-bach 1f2a0400.bach3: pcmP2 dma buffer size 0x40000 sstar-bach 1f2a0400.bach3: physical dma address 0x24e10000 sstar-bach 1f2a0400.bach3: miu address 0x04e10000 sstar-bach 1f2a0400.bach3: virtual dma address (ptrval) sstar-asoc-card soc:asoc3_sound: ASoC: driver name too long 'sstar-asoc3-card' -> 'sstar-asoc3-car' NET: Registered PF_PACKET protocol family sstar_pm_init init ... Registering SWP/SWPB emulation handler Loading compiled-in X.509 certificates Key type .fscrypt registered Key type fscrypt-provisioning registered Key type encrypted registered ubi0: attaching mtd10 ubi0: scanning is finished ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 9, need 20 ubi0: attached mtd10 (name "ubia", size 104 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 837, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 886906549 ubi0: available PEBs: 0, total reserved PEBs: 837, PEBs reserved for bad PEB handling: 9 ubi0: background thread "ubi_bgt0d" started, PID 473 OF: fdt: not creating '/sys/firmware/fdt': CRC check failed clk: Disabling unused clocks ALSA device list: #0: sstar-asoc-card #1: sstar-asoc2-card #2: sstar-asoc3-card mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. VFS: Mounted root (squashfs filesystem) readonly on device 31:7. devtmpfs: mounted Freeing unused kernel image (initmem) memory: 1024K Run /linuxrc as init process random: crng init done net.core.rmem_default = 163840 net.core.rmem_max = 163840 net.core.wmem_default = 524288 net.core.wmem_max = 1048576 net.ipv4.tcp_mem = 924 1232 1848 net.ipv4.tcp_rmem = 4096 87380 325120 net.ipv4.tcp_wmem = 4096 131072 393216 /etc/init.d/rcS: line 16: resize2fs: not found /etc/init.d/rcS: line 17: UBIFS (ubi0:0): Mounting in unauthenticated mode UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 489 resize2fs: not found UBIFS (ubi0:0): recovery needed UBIFS (ubi0:0): recovery completed UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "miservice" UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 19427328 bytes (18 MiB, 153 LEBs), max 163 LEBs, journal size 2920448 bytes (2 MiB, 23 LEBs) UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID 3C18967F-076F-4B9A-8442-6E3EA08CE71D, small LPT model UBIFS (ubi0:1): Mounting in unauthenticated mode UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 492 UBIFS (ubi0:1): recovery needed UBIFS (ubi0:1): recovery completed UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "customer" /etc/init.d/rcS: line 22: fwfs: not found insmod: can't read '/config/modules/6.1/nfs_ssc.ko': No such file or directory insmod: can't read '/config/modules/6.1/libarc4.ko': No such file or directory insmod: can't read '/config/modules/6.1/scsi_mod.ko': No such file or directory insmod: can't read '/config/modules/6.1/md4.ko': No such file or directory insmod: can't read '/config/modules/6.1/seqiv.ko': No such file or directory insmod: can't read '/config/modules/6.1/libdes.ko': No such file or directory insmod: can't read '/config/modules/6.1/grace.ko': No such file or directory insmod: can't read '/config/modules/6.1/sunrpc.ko': No such file or directory insmod: can't read '/config/modules/6.1/lockd.ko': No such file or directory insmod: can't read '/config/modules/6.1/nfs.ko': No such file or directory Fail to get pad(0x0) ip(0x0_8) form padmux ! SDMMC0 >> [Hal_CARD_SetBustiming] DEFS mode. << insmod: can't read '/config/modules/6.1/sd_mod.ko': No such file or directory err: i2c-3 write start err! err: i2c-3 stop signal err! err:i2c-3 xfer error: -7 Goodix-TS 3-005d: Error reading 1 bytes from 0x8140: -1 err: i2c-3 write start err! err: i2c-3 stop signal err! err:i2c-3 xfer error: -7 Goodix-TS 3-005d: Error reading 1 bytes from 0x8140: -1 Goodix-TS 3-005d: I2C communication failure: -1 insmod: can't read '/config/modules/6.1/pstore.ko': No such file or directory insmod: can't read '/config/modules/6.1/pstore_zone.ko': No such file or directory insmod:err: i2c-2 err dma write transform len:0 != para_len:2 err:i2c-2 xfer error: -7 rtc-hym8563 2-0051: could not init device, -1 can't read '/config/modules/6.1/pstore_blk.ko': No such file or directory module [sys] init 2024-12-16_10-24-26 mma_heap_name0,miu=0,sz=a00000,reserved_start=27600000 mi_sys_mma_allocator_create success, heap_base_addr=27600000 length=a00000 mma_heap_fb,miu=0,sz=708000,reserved_start=25cf7000 mi_sys_mma_allocator_create success, heap_base_addr=25cf7000 length=708000 mi_sys_mma_allocator_create success, heap_base_addr=20000000 length=43800 protect_panic_on: 0 snr_sr0_par_mode = 2 snr_sr0_par_rst_mode: no value!! snr_sr0_par_pdn_mode: no value!! snr_sr0_par_mclk_mode = 2 snr_sr0_bt656_mode = 1 snr_sr0_bt656_rst_mode: no value!! snr_sr0_bt656_pdn_mode: no value!! snr_sr0_bt656_mclk_mode = 2 snr_sr0_mipi_mode = 5 snr_sr0_mipi_rst_mode: no value!! snr_sr0_mipi_pdn_mode: no value!! snr_sr0_mipi_mclk_mode = 1 snr_sr2_mipi_mode = 5 snr_sr2_mipi_rst_mode: no value!! snr_sr2_mipi_pdn_mode: no value!! snr_sr2_mipi_mclk_mode = 1 snr_sr0_rst_gpio = 69 snr_sr2_rst_gpio = 65 snr_sr0_pdn_gpio = 65 snr0_paral_i2c = 0 snr0_mipi_i2c = 1 snr2_mipi_i2c = 0 module [sensor] init module [rgn] init [RGN] osd blending : disable module [gfx] init module [disp] init [FB] keep bootlogo: false module [fb] init module [dummy] init module [vif] init [VIF] vif0ch int irq 82 [VIF] vif0dma int irq 83 [VIF] clk 0 [VIF] clk 1 mhal module [isp] init [ISP Driver init] [DRV_ISP_WORK_EarlyInit] ==================== >>>>>>>>>> [DRV_ISP_CLK_Register] clk_isp enable 0 [DRV_ISP_CLK_Register] clk_isp enable 1 [DRV_ISP_CLK_Register] clk_isp enable 2 [DRV_ISP_CLK_Init] Use Preset Idx [0] [DRV_ISP_Open][0] oooooooooooooooooooo >>>>>>>>>> [DRV_ISP_Open] Dev ID = 0 Hal=0xc0e7ce00 [DRV_ISP_PROXY_Isp0Probe] Dev=0, pHnd=0xbfc37348 [ISP] Request IRQ Num: 84 [LIBCAMERA_IspMidEarlyInit] ==================== >>>>>>>>>> module [isp] init module [scl] init module [pspi] init module [vdisp] init module [ipu] init CmdqProcInit 1178 mi sys debug init success MI_SYS_Dump_Common_Info_Init is success mi sensor debug init success mi vif debug init success mi RGN debug init success mi disp debug init success mi wbc debug init success mi pspi debug init success mi GFX debug init success mi scl debug init success mi isp debug init success mi FB debug init success mi vdisp debug init success mi ipu debug init success module [debug] init pad 0 register pad 2 register Gadget configfs UDC:1f284200.msb250x-udc-p0 /customer/ssh/sbin/sshd: can't load library 'libfts.so.0' / # adb连接登陆 ~~~~~~~~~~~~~ .. code-block:: shell #需要TYPEC线供电 #打开win10电脑的cmd输入终端 #输入adb shell和ls,如下： adb shell / # ls bin busybox-1.20.2-arm-buildroot-linux-uclibcgnueabihf-uclibc-12.4.0-dynamic.tar.gz config customer dev etc home lib linuxrc misc mnt proc run sbin sys tmp usr var / # #可以看到文件，说明已经登录完成 网线telnetd登录 ~~~~~~~~~~~~~~~~~ .. code-block:: shell #需要插上网线和配置IP地址，以及telnetd(我的电脑IP地址为192.168.137.99) $ ifconfig eth0 192.168.137.81 $ telnetd #可以串口软件登陆，如 #点击串口file->New #设置Protocol选择TELNET #host设置为192.168.137.81 #点击Connect连接 #用户名是root，没有密码，直接敲回车登陆，如下 login: can\'t chdir to home directory '/home/root' / # ls bin busybox-1.20.2-arm-buildroot-linux-uclibcgnueabihf-uclibc-12.4.0-dynamic.tar.gz config customer dev etc home lib linuxrc misc mnt proc run sbin sys tmp usr var / #