MYZR-SSD2351-EK112快速启动手册
准备工作
开发板：1个
TYPEC数据线：1条
TTL串口模块：1个
杜板线：若干
网线：1根
串口软件设置
波特率：115200
数据位：8bit
停止位：1bit
校验位：none
拨码设置以及TTL串口模块
拨码设置
启动拨码模式：1: on， 2: on， 3: off， 4 : off
TTL串口模块接法
座子：J3
按以下CPU的对应端和TTL模块的管脚连接起来
CPU端： |
J3_1:RX管脚(正方形焊盘) |
J3_2:TX管脚 |
J3_3:地 |
|---|---|---|---|
TTL端： |
TX管脚 |
RX管脚 |
GND |
串口启动
#用TTL模块，把电脑和板子连接起来。插入TYPEC线，开机
提示信息如下：
IPL gf7fc380
D-19
CPU=800MHz
HEAP: [0xa0018330~0xa0018430]
SHM: [0xa0013830~0xa0018330]
RECORD: tc at 0xa00138c0
HW Reset
SPI 104M
[SPINAND] RFC use command 0x6b
[SPINAND] dummy clock 0x8
[SPINAND] Program with command 0x32.
[SPINAND] Random with command 0x34.
[FLASH] BDMA mode.
Loading Environment from SPIFlash...
OK
QFN128 NTC1G DDR3 DFS(2133, 800)
miu pll: 300MHz
DRAM Size: 128MB
ddr train finish
HEAP: [0x23d00000~0x23e00000]
SHM: [0x22440000~0x23d00000 0x7dbd3830]
IMG_LOAD@ devs:0xa img:CUST bak:0 ofs:0x0 sz:0x580 dst:0x23d00000
IMG_LOAD@ devs:0xa img:CUST bak:0 ofs:0x0 sz:0x7520 dst:0x22400000
IMG_VERIFY@ type:1
DECOMP@0 from 0x22400000 to 0x22400000
Flashing D-Cache and Disabling MMU
OS_JUMP@ method:1 entry_pointer:0x22400000
IPL_CUST gf7fc380
D-19
HEAP: [0x23d00000~0x23e00000]
RECORD: moving tc from 0x22440090 to 0x263ff000
SPI 104M
IMG_LOAD@ devs:0xa img:TFA bak:0 ofs:0x0 sz:0x580 dst:0x23d00000
IMG_LOAD@ devs:0xa img:TFA bak:0 ofs:0x0 sz:0xc10a dst:0x263fffc0
IMG_VERIFY@ type:2
DECOMP@0 from 0x26400000 to 0x26400000
IMG_LOAD@ devs:0xa img:UBOOT bak:0 ofs:0x0 sz:0x580 dst:0x23d00580
IMG_LOAD@ devs:0xa img:UBOOT bak:0 ofs:0x0 sz:0x55268 dst:0x22444680
IMG_VERIFY@ type:4
DECOMP@2 from 0x224446c0 to 0x23e00000
Flashing D-Cache
OS_JUMP@ method:2 entry_pointer:0x23e00000
U-Boot 2021.10 (Mar 03 2025 - 07:57:25 +0000)
SoC: SigmaStar pcupid
Model: PCUPID
Version: P###g#######
DRAM: 128 MiB
WDT: Not found!
NAND: SPI 104M
[SPINAND] RFC use command 0x6b
[SPINAND] dummy clock 0x8
[SPINAND] Program with command 0x32.
[SPINAND] Random with command 0x34.
[FLASH] BDMA mode.
spi clk already initialized
[FLASH] dev_id = 0xee
[FLASH] mfr_id = 0xc8, dev_id= 0x91 id_len = 0x2
128 MiB
MMC: Fail to get pad(0x20309) ip(0x2_8) form padmux !
Fail to get pad(0x20003) ip(0x0_2) form padmux !
MSC: 0, MSC: 1
Loading Environment from NAND...
ENV: offset = 0x4c0000 size = 0x40000
ENV1: offset = 0x500000 size = 0x40000
OK
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
firmwarefs_open: open PQ.bin fail(-2)
JPD_SW_decode time: 74259 us
JPD_SW_decode time: 13134 us
cost time: 508815 us
bitwidth = 16
## Booting kernel from Legacy Image at 23000000 ...
Image Name: MVX4##P###g#######KL_LX601##[BR:
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 3436492 Bytes = 3.3 MiB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Uncompressing Kernel Image
[XZ] !!!reserved 0x22000000 length=0x 1000000 for xz!!
XZ: uncompressed size=0x9651ec, ret=7
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 6.1.111-rt42 (tangbin@myzr-u2004) (arm-sigmastar-linux-uclibcgnueabihf-12.4.0-gcc (crosstool-NG 1.26.0) 12.4.0, GNU ld (crosstool-NG 1.26.0) 2.40) #120 SMP PREEMPT Wed Mar 5 04:14:41 UTC 2025
CPU: ARMv7 Processor [411fd040] revision 0 (ARMv7), cr=50c5383d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
early_atags_to_fdt() success
OF: fdt: Machine model: PCUPID
LXmem is 0x8000000 PHYS_OFFSET is 0x20000000
Add mem start 0x20000000 size 0x8000000!!!!
LX_MEM = 0x20000000, 0x8000000
LX_MEM2 = 0x0, 0x0
LX_MEM3 = 0x0, 0x0
MMU_MEM = 0x0, 0x0
EMAC_LEN= 0x0
DRAM_LEN= 0x0
Memory policy: Data cache writealloc
OF: reserved mem: invalid size property in 'cma0' node.
deal_with_reserved_mmap memblock_reserve success mmap_reserved_config[0].reserved_start=
0x26800000
deal_with_reserve_mma_heap memblock_reserve success mma_config[0].reserved_start=
0x27600000 size:a00000
deal_with_reserve_mma_heap memblock_reserve success mma_config[1].reserved_start=
0x25cf7000 size:708000
cma: Reserved 16 MiB at 0x24c00000
Zone ranges:
Normal [mem 0x0000000020000000-0x00000000275fffff]
HighMem empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000020000000-0x0000000025cf6fff]
node 0: [mem 0x00000000263ff000-0x00000000275fffff]
Initmem setup node 0 [mem 0x0000000020000000-0x00000000275fffff]
On node 0, zone Normal: 776 pages in unavailable ranges
psci: probing for conduit method from DT.
psci: PSCIv1.1 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: MIGRATE_INFO_TYPE not supported.
psci: SMC Calling Convention v1.2
percpu: Embedded 11 pages/cpu s15584 r8192 d21280 u45056
Built 1 zonelists, mobility grouping on. Total pages: 28172
Kernel command line: ubi.mtd=ubia,2048 root=/dev/mtdblock7 rootfstype=squashfs ro init=/linuxrc LX_MEM=0x8000000 mma_heap=mma_heap_name0,miu=0,sz=0xA00000 mma_memblock_remove=1 cma=16M mma_heap=mma_heap_fb,miu=0,sz=0x708000 mmap_reserved=fb,miu=0,sz=0x800000,max_start_off=0x6800000,max_end_off=0x7000000 mtdparts=nand0:1792k@1280k(BOOT),1792k(BOOT_BAK),256k(ENV),256k(ENV1),384k(DDRTRAIN),5m(KERNEL),5m(RECOVERY),6m(rootfs),768k(vendor_storage),1m(MISC),107136k(ubia)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
mem auto-init: stack:all(zero), heap alloc:off, heap free:off
Memory: 77488K/113632K available (4096K kernel code, 436K rwdata, 2192K rodata, 1024K init, 157K bss, 19760K reserved, 16384K cma-reserved, 0K highmem)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
rcu: Preemptible hierarchical RCU implementation.
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
GICv3: 192 SPIs implemented
GICv3: 0 Extended SPIs implemented
GICv3: GICv3 features: 16 PPIs
GICv3: CPU0: found redistributor 0 region 0:0x16080000
sstar_main_intc_init: np->name=sstar_main_intc, parent=gic
sstar_pm_main_intc_init: np->name=sstar_pm_main_intc, parent=sstar_main_intc
sstar_gpi_intc_init: np->name=sstar_gpi_intc, parent=sstar_main_intc
sstar_pm_gpi_intc_init: np->name=sstar_pm_gpi_intc, parent=sstar_main_intc
rcu: srcu_init: Setting srcu_struct sizes based on contention.
[hal_clk_ipupll_init] ipupll already init, skip
arch_timer: cp15 timer(s) running at 6.00MHz (virt).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1623fa770, max_idle_ns: 440795202238 ns
sched_clock: 56 bits at 6MHz, resolution 166ns, wraps every 4398046511055ns
Switching to timer-based delay loop, resolution 166ns
printk: console [ttyS0] enabled
Calibrating delay loop (skipped), value calculated using timer frequency.. 12.00 BogoMIPS (lpj=60000)
CPU: Testing write buffer coherency: ok
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x20100000 - 0x20100054
rcu: Hierarchical SRCU implementation.
rcu: Max phase no-delay instances is 1000.
printk: console [ttyS0] printing thread started
smp: Bringing up secondary CPUs ...
GICv3: CPU1: found redistributor 1 region 0:0x160a0000
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
GICv3: CPU2: found redistributor 2 region 0:0x160c0000
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
GICv3: CPU3: found redistributor 3 region 0:0x160e0000
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
smp: Brought up 1 node, 4 CPUs
SMP: Total of 4 processors activated (48.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 40 variant 4 rev 3
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 16 (order: -2, 1024 bytes, linear)
NET: Registered PF_NETLINK/PF_ROUTE protocol family
DMA: preallocated 256 KiB pool for atomic coherent allocations
Version : MVX4##P###g#######KL_LX601##[BR:g]#XVM
platform soc: Fixed dependency cycle(s) with /soc/sstar_main_intc
GPIO: probe end
[Padmux]reset PAD9(reg 0x103c00:49; mask0x8000) t0 SDIO_MODE_2 (org: SD_BOOT_MODE_1)
[Padmux]reset PAD79(reg 0x153f00:70; mask0x1) t0 FUART1_MODE_3 (org: OUTP_RX0_CH0_IE_CLR_MODE_0)
[Padmux]reset PAD80(reg 0x153f00:70; mask0x2) t0 FUART1_MODE_3 (org: OUTN_RX0_CH0_IE_CLR_MODE_0)
[Padmux]reset PAD81(reg 0x153f00:70; mask0x4) t0 FUART1_MODE_3 (org: OUTP_RX0_CH1_IE_CLR_MODE_0)
[Padmux]reset PAD82(reg 0x153f00:70; mask0x8) t0 FUART1_MODE_3 (org: OUTN_RX0_CH1_IE_CLR_MODE_0)
[Padmux]reset PAD83(reg 0x153f00:70; mask0x10) t0 FUART2_MODE_3 (org: OUTP_RX0_CH2_IE_CLR_MODE_0)
[Padmux]reset PAD84(reg 0x153f00:70; mask0x20) t0 FUART2_MODE_3 (org: OUTN_RX0_CH2_IE_CLR_MODE_0)
[Padmux]reset PAD85(reg 0x153f00:70; mask0x40) t0 FUART2_MODE_3 (org: OUTP_RX0_CH3_IE_CLR_MODE_0)
[Padmux]reset PAD86(reg 0x153f00:70; mask0x80) t0 FUART2_MODE_3 (org: OUTN_RX0_CH3_IE_CLR_MODE_0)
[Padmux]reset PAD96(reg 0x103c00:64; mask0x7) t0 FUART3_2W_MODE_2 (org: MIPI_TX_MODE_1)
[Padmux]reset PAD96(reg 0x153400:5c; mask0x1) t0 FUART3_2W_MODE_2 (org: OUTP_CH0_IE_CLR_MODE_0)
[Padmux]reset PAD97(reg 0x153400:5c; mask0x100) t0 FUART3_2W_MODE_2 (org: OUTN_CH0_IE_CLR_MODE_0)
[Padmux]reset PAD16(reg 0x103e00:10; mask0x8) t0 UART5_MODE_3 (org: GPIO_MODE)
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
SCSI subsystem initialized
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
[MIU ERR] [sstar_miu_clk_register@532] [sstar_miu_clk_register] clk_miu enable 0
[hal_clk_mtcmos_isp_enable] clk_mtcmos_isp already enabled!
Do qos-initialize
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.22
NET: Registered PF_BLUETOOTH protocol family
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
clocksource: Switched to clocksource arch_sys_counter
NET: Registered PF_INET protocol family
IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 5120 bytes, linear)
Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
TCP bind hash table entries: 1024 (order: 3, 40960 bytes, linear)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 128 (order: 0, 6144 bytes, linear)
UDP-Lite hash table entries: 128 (order: 0, 6144 bytes, linear)
NET: Registered PF_UNIX/PF_LOCAL protocol family
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Initialise system trusted keyrings
workingset: timestamp_bits=30 max_order=15 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. © 2001-2006 Red Hat, Inc.
fuse: init (API version 7.38)
Key type asymmetric registered
Asymmetric key parser 'x509' registered
io scheduler mq-deadline registered
io scheduler kyber registered
mousedev: PS/2 mouse device common for all mice
i2c_dev: i2c /dev entries driver
Bluetooth: HCI UART driver ver 2.3
Bluetooth: HCI UART protocol H4 registered
Bluetooth: HCI UART protocol Three-wire (H5) registered
SMCCC: SOC_ID: ID = jep106:0000:8192 Revision = 0x00000000
no urdma irq resource defined
no urdma irq resource defined
no urdma irq resource defined
no urdma irq resource defined
no urdma irq resource defined
no urdma irq resource defined
no urdma irq resource defined
no urdma irq resource defined
no urdma irq resource defined
mdio_bus mdio-bus@emac0: ethernet-phy@0 has invalid PHY address
mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 0
mdio_bus mdio-bus@emac0: scan phy ethernet-phy at address 1
[emac_phy_connect][2999] connected mac emac0 to PHY at mdio-bus@emac0:01 [uid=02430c54, driver=Generic PHY]
sstar,rtcpwc 1f006800.rtcpwc: registered as rtc0
sstar,rtcpwc 1f006800.rtcpwc: setting system clock to 1970-01-01T00:28:46 UTC (1726)
input: rtcpwc as /devices/soc0/soc/1f006800.rtcpwc/input/input0
[Padmux]reset PAD18(reg 0x103e00:12; mask0x8) t0 I2C2_MODE_3 (org: GPIO_MODE)
[Padmux]reset PAD19(reg 0x103e00:13; mask0x8) t0 I2C2_MODE_3 (org: GPIO_MODE)
[Padmux]reset PAD126(reg 0x103e00:7e; mask0x8) t0 I2C3_MODE_2 (org: GPIO_MODE)
[Padmux]reset PAD125(reg 0x103e00:7d; mask0x8) t0 I2C3_MODE_2 (org: GPIO_MODE)
[sstar_cpufreq_init] Current clk=800000000
request for verification of policy (0 - 2147483647 kHz) for cpu 0
verification lead to (200000 - 1450000 kHz) for cpu 0
sstar_pwm_probe: fail to config dead time
sstar_pwm_probe: fail to config dead time
sstar_pwm_probe: fail to config dead time
sstar_pwm_probe: fail to config dead time
sstar_pwm_probe: fail to config dead time
sstar_pwm_probe: fail to config dead time
spi 1f222000.spi: chipselect 0 already in use
spi_master spi0: spi_device register error /soc/spi@1f222000/spidev@0
spi_master spi0: Failed to create SPI device for /soc/spi@1f222000/spidev@0
SPI 104M
[SPINAND] RFC use command 0x6b
[SPINAND] dummy clock 0x8
[SPINAND] Program with command 0x32.
[SPINAND] Random with command 0x34.
[FLASH] BDMA mode.
[FLASH] dev_id = 0xee
[FLASH] mfr_id = 0xc8, dev_id= 0x91 id_len = 0x2
nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x91
nand: Unknown nand0
nand: 128 MiB, MLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: nand0: the ECC used on your system (4b/512B) is too weak compared to the one required by the NAND chip (512b/4B)
11 cmdlinepart partitions found on MTD device nand0
Creating 11 MTD partitions on "nand0":
0x000000140000-0x000000300000 : "BOOT"
0x000000300000-0x0000004c0000 : "BOOT_BAK"
0x0000004c0000-0x000000500000 : "ENV"
0x000000500000-0x000000540000 : "ENV1"
0x000000540000-0x0000005a0000 : "DDRTRAIN"
0x0000005a0000-0x000000aa0000 : "KERNEL"
0x000000aa0000-0x000000fa0000 : "RECOVERY"
0x000000fa0000-0x0000015a0000 : "rootfs"
0x0000015a0000-0x000001660000 : "vendor_storage"
0x000001660000-0x000001760000 : "MISC"
0x000001760000-0x000008000000 : "ubia"
Err: Could not get dts [wakeup] option!
wakeup: probe of soc:wakeup failed with error 1
sstar-asoc-card soc:asoc_sound: i = 0, codec_name = sstar-dummy-codec1
sstar-bach 1f2a0400.bach1: pcmC0 dma buffer size 0x40000
sstar-bach 1f2a0400.bach1: physical dma address 0x24c50000
sstar-bach 1f2a0400.bach1: miu address 0x04c50000
sstar-bach 1f2a0400.bach1: virtual dma address (ptrval)
sstar-bach 1f2a0400.bach1: pcmP0 dma buffer size 0x100000
sstar-bach 1f2a0400.bach1: physical dma address 0x24c90000
sstar-bach 1f2a0400.bach1: miu address 0x04c90000
sstar-bach 1f2a0400.bach1: virtual dma address (ptrval)
sstar-asoc-card soc:asoc2_sound: i = 0, codec_name = sstar-dummy-codec2
sstar-bach 1f2a0400.bach2: pcmC1 dma buffer size 0x40000
sstar-bach 1f2a0400.bach2: physical dma address 0x24d90000
sstar-bach 1f2a0400.bach2: miu address 0x04d90000
sstar-bach 1f2a0400.bach2: virtual dma address (ptrval)
sstar-bach 1f2a0400.bach2: pcmP1 dma buffer size 0x40000
sstar-bach 1f2a0400.bach2: physical dma address 0x24dd0000
sstar-bach 1f2a0400.bach2: miu address 0x04dd0000
sstar-bach 1f2a0400.bach2: virtual dma address (ptrval)
sstar-asoc-card soc:asoc2_sound: ASoC: driver name too long 'sstar-asoc2-card' -> 'sstar-asoc2-car'
sstar-asoc-card soc:asoc3_sound: i = 0, codec_name = sstar-dummy-codec3
sstar-bach 1f2a0400.bach3: pcmC0 dma buffer size 0x40000
sstar-bach 1f2a0400.bach3: physical dma address 0x24c50000
sstar-bach 1f2a0400.bach3: miu address 0x04c50000
sstar-bach 1f2a0400.bach3: virtual dma address (ptrval)
sstar-bach 1f2a0400.bach3: pcmP2 dma buffer size 0x40000
sstar-bach 1f2a0400.bach3: physical dma address 0x24e10000
sstar-bach 1f2a0400.bach3: miu address 0x04e10000
sstar-bach 1f2a0400.bach3: virtual dma address (ptrval)
sstar-asoc-card soc:asoc3_sound: ASoC: driver name too long 'sstar-asoc3-card' -> 'sstar-asoc3-car'
NET: Registered PF_PACKET protocol family
sstar_pm_init init ...
Registering SWP/SWPB emulation handler
Loading compiled-in X.509 certificates
Key type .fscrypt registered
Key type fscrypt-provisioning registered
Key type encrypted registered
ubi0: attaching mtd10
ubi0: scanning is finished
ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 9, need 20
ubi0: attached mtd10 (name "ubia", size 104 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 837, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 886906549
ubi0: available PEBs: 0, total reserved PEBs: 837, PEBs reserved for bad PEB handling: 9
ubi0: background thread "ubi_bgt0d" started, PID 473
OF: fdt: not creating '/sys/firmware/fdt': CRC check failed
clk: Disabling unused clocks
ALSA device list:
#0: sstar-asoc-card
#1: sstar-asoc2-card
#2: sstar-asoc3-card
mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
devtmpfs: mounted
Freeing unused kernel image (initmem) memory: 1024K
Run /linuxrc as init process
random: crng init done
net.core.rmem_default = 163840
net.core.rmem_max = 163840
net.core.wmem_default = 524288
net.core.wmem_max = 1048576
net.ipv4.tcp_mem = 924 1232 1848
net.ipv4.tcp_rmem = 4096 87380 325120
net.ipv4.tcp_wmem = 4096 131072 393216
/etc/init.d/rcS: line 16: resize2fs: not found
/etc/init.d/rcS: line 17: UBIFS (ubi0:0): Mounting in unauthenticated mode
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 489
resize2fs: not found
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "miservice"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 19427328 bytes (18 MiB, 153 LEBs), max 163 LEBs, journal size 2920448 bytes (2 MiB, 23 LEBs)
UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID 3C18967F-076F-4B9A-8442-6E3EA08CE71D, small LPT model
UBIFS (ubi0:1): Mounting in unauthenticated mode
UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 492
UBIFS (ubi0:1): recovery needed
UBIFS (ubi0:1): recovery completed
UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "customer"
/etc/init.d/rcS: line 22: fwfs: not found
insmod: can't read '/config/modules/6.1/nfs_ssc.ko': No such file or directory
insmod: can't read '/config/modules/6.1/libarc4.ko': No such file or directory
insmod: can't read '/config/modules/6.1/scsi_mod.ko': No such file or directory
insmod: can't read '/config/modules/6.1/md4.ko': No such file or directory
insmod: can't read '/config/modules/6.1/seqiv.ko': No such file or directory
insmod: can't read '/config/modules/6.1/libdes.ko': No such file or directory
insmod: can't read '/config/modules/6.1/grace.ko': No such file or directory
insmod: can't read '/config/modules/6.1/sunrpc.ko': No such file or directory
insmod: can't read '/config/modules/6.1/lockd.ko': No such file or directory
insmod: can't read '/config/modules/6.1/nfs.ko': No such file or directory
Fail to get pad(0x0) ip(0x0_8) form padmux !
SDMMC0 >> [Hal_CARD_SetBustiming] DEFS mode. <<
insmod: can't read '/config/modules/6.1/sd_mod.ko': No such file or directory
err: i2c-3 write start err!
err: i2c-3 stop signal err!
err:i2c-3 xfer error: -7
Goodix-TS 3-005d: Error reading 1 bytes from 0x8140: -1
err: i2c-3 write start err!
err: i2c-3 stop signal err!
err:i2c-3 xfer error: -7
Goodix-TS 3-005d: Error reading 1 bytes from 0x8140: -1
Goodix-TS 3-005d: I2C communication failure: -1
insmod: can't read '/config/modules/6.1/pstore.ko': No such file or directory
insmod: can't read '/config/modules/6.1/pstore_zone.ko': No such file or directory
insmod:err: i2c-2 err dma write transform len:0 != para_len:2
err:i2c-2 xfer error: -7
rtc-hym8563 2-0051: could not init device, -1
can't read '/config/modules/6.1/pstore_blk.ko': No such file or directory
module [sys] init 2024-12-16_10-24-26
mma_heap_name0,miu=0,sz=a00000,reserved_start=27600000
mi_sys_mma_allocator_create success, heap_base_addr=27600000 length=a00000
mma_heap_fb,miu=0,sz=708000,reserved_start=25cf7000
mi_sys_mma_allocator_create success, heap_base_addr=25cf7000 length=708000
mi_sys_mma_allocator_create success, heap_base_addr=20000000 length=43800
protect_panic_on: 0
snr_sr0_par_mode = 2
snr_sr0_par_rst_mode: no value!!
snr_sr0_par_pdn_mode: no value!!
snr_sr0_par_mclk_mode = 2
snr_sr0_bt656_mode = 1
snr_sr0_bt656_rst_mode: no value!!
snr_sr0_bt656_pdn_mode: no value!!
snr_sr0_bt656_mclk_mode = 2
snr_sr0_mipi_mode = 5
snr_sr0_mipi_rst_mode: no value!!
snr_sr0_mipi_pdn_mode: no value!!
snr_sr0_mipi_mclk_mode = 1
snr_sr2_mipi_mode = 5
snr_sr2_mipi_rst_mode: no value!!
snr_sr2_mipi_pdn_mode: no value!!
snr_sr2_mipi_mclk_mode = 1
snr_sr0_rst_gpio = 69
snr_sr2_rst_gpio = 65
snr_sr0_pdn_gpio = 65
snr0_paral_i2c = 0
snr0_mipi_i2c = 1
snr2_mipi_i2c = 0
module [sensor] init
module [rgn] init
[RGN] osd blending : disable
module [gfx] init
module [disp] init
[FB] keep bootlogo: false
module [fb] init
module [dummy] init
module [vif] init
[VIF] vif0ch int irq 82
[VIF] vif0dma int irq 83
[VIF] clk 0
[VIF] clk 1
mhal module [isp] init
[ISP Driver init]
[DRV_ISP_WORK_EarlyInit] ==================== >>>>>>>>>>
[DRV_ISP_CLK_Register] clk_isp enable 0
[DRV_ISP_CLK_Register] clk_isp enable 1
[DRV_ISP_CLK_Register] clk_isp enable 2
[DRV_ISP_CLK_Init] Use Preset Idx [0]
[DRV_ISP_Open][0] oooooooooooooooooooo >>>>>>>>>>
[DRV_ISP_Open] Dev ID = 0 Hal=0xc0e7ce00
[DRV_ISP_PROXY_Isp0Probe] Dev=0, pHnd=0xbfc37348
[ISP] Request IRQ Num: 84
[LIBCAMERA_IspMidEarlyInit] ==================== >>>>>>>>>>
module [isp] init
module [scl] init
module [pspi] init
module [vdisp] init
module [ipu] init
CmdqProcInit 1178
mi sys debug init success
MI_SYS_Dump_Common_Info_Init is success
mi sensor debug init success
mi vif debug init success
mi RGN debug init success
mi disp debug init success
mi wbc debug init success
mi pspi debug init success
mi GFX debug init success
mi scl debug init success
mi isp debug init success
mi FB debug init success
mi vdisp debug init success
mi ipu debug init success
module [debug] init
pad 0 register
pad 2 register
Gadget configfs UDC:1f284200.msb250x-udc-p0
/customer/ssh/sbin/sshd: can't load library 'libfts.so.0'
/ #
adb连接登陆
#需要TYPEC线供电
#打开win10电脑的cmd输入终端
#输入adb shell和ls,如下：
adb shell
/ # ls
bin
busybox-1.20.2-arm-buildroot-linux-uclibcgnueabihf-uclibc-12.4.0-dynamic.tar.gz
config
customer
dev
etc
home
lib
linuxrc
misc
mnt
proc
run
sbin
sys
tmp
usr
var
/ #
#可以看到文件，说明已经登录完成
网线telnetd登录
#需要插上网线和配置IP地址，以及telnetd(我的电脑IP地址为192.168.137.99)
$ ifconfig eth0 192.168.137.81
$ telnetd
#可以串口软件登陆，如
#点击串口file->New
#设置Protocol选择TELNET
#host设置为192.168.137.81
#点击Connect连接
#用户名是root，没有密码，直接敲回车登陆，如下
login: can\'t chdir to home directory '/home/root'
/ # ls
bin
busybox-1.20.2-arm-buildroot-linux-uclibcgnueabihf-uclibc-12.4.0-dynamic.tar.gz
config
customer
dev
etc
home
lib
linuxrc
misc
mnt
proc
run
sbin
sys
tmp
usr
var
/ #